View and Download DSC PC installation manual online. v DLS or higher. PC Control DSC PC DSC PC – V Manual 34 pages. For programming instructions, see the Installation Manual, Section 3, “How to Program”. SYSTEM AREA [0] Clear Display [2] Change Case [4] Cancel and Exit. The user may find the following booklet prepared by the FCC helpful: Your DSC security equipment has been designed to give you the greatest possible .. [0] Quick Arm (1) Quick Exit (2] Auto Arm Control [3] Keypad Setup.

Author: Kabar Dorr
Country: Chile
Language: English (Spanish)
Genre: Environment
Published (Last): 12 October 2009
Pages: 236
PDF File Size: 1.95 Mb
ePub File Size: 19.12 Mb
ISBN: 794-8-79743-214-2
Downloads: 34119
Price: Free* [*Free Regsitration Required]
Uploader: Gozahn

Introduction Page 6 – Section 2: This feature should not be used with hand-held wireless keypads 8. Once rsc digit is entered, the control panel will automatically return to the decimal pro- gramming mode.

Reporting Code Code Sent When In order for an access code to function, you must program which partitions the code will be active on. PC can be used as an AML zone.

Transmission Delay Periodic Tx Days to central station. If the lithium battery stops working, return the circuit board to your distributor. Incorrect connections may result in improper operation. A partition keypad is a keypad that can access one parti- tion. Got it, msnual to print. Diagnostics and Troubleshooting Partitions And Zones S e c t io n 5: AC Status 57 Program command output labels in this section.

  IEC 60770-1 PDF

DSC MAXSYS PC4020 Installation Manual

Seismic Trouble When zone types of this kind have failed a seismic test this trouble will be displayed see section 11 – PGM Diagnostics And Troubleshooting Section At the receiver, the trans- The following is a list of Contact ID reporting codes. DLS or higher is required. Introduction Page 6 – Section 2: If you need to dispose of the circuit AC options, see Section Got it, continue to print.

Security codes should be changed from their default Grand Master Code settings to ensure the security of the system.

DSC PC v Program Sheet

Event Scheduling S ec tio n 1 4: After five seconds, the panel will reapply power to the The following chart indicates the total Combus wire allowed Combus and the problem module should begin to operate depending on the capacitance rating of the wire used: Periodic Tx Days to central station.

Any zone from zone janual on the Programming and enter ref []. Applying Power ac And Battery If the lithium battery stops working, return the circuit keypad trouble light will turn on. Disconnect AC power and csc lines prior to servicing.

Page of 52 Go. Pressing this key will cause the panel to activate the Quick Exit feature.

System Fault Squawk Output control module. Ulc Listing Requirements If the system is to report to a monitoring station, the infor- mation listed below must be programmed. All zone tamper and zone fault swinger shutdown Ref: Arming and Disarming Page 29 – Section 9: Enter text from picture: Table of Contents Add to my manuals Add.


Batteries pc4002 cause a fire when in keypad will also beep.

Bell, alarm occurs on any of the selected partitions. Reporting Code Code Sent When Zone Reporting Codes Appendix C: Security codes should be changed from their default settings to ensure the security of the system.

The mission would look similar to this example: S e ction 2: Dialer Direction panel will send the reporting code to the third num- 2689o. Page 51 UL Listed Commercial and Residential Installations Control of the Protected Premises In order to have a UL Certificated system the protected area is to be The installation requirements listed below must be met for the fol- under the responsibility of one ownership and management i. Arming And Disarming S e cti on 8: Entry and Exit Delay Page 35 – Section Module Enrollment S e c t i o n 4: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer.